Fits Your Existing Lock - Locked Doors Keep Insurers Happy

Nothing Drilled • 30-day returns • Free UK delivery over £85 • 1-Year warranty

🛒Basket
✓ Added to basket View basketCheckout →
Works with Matter

Fitting the Matter Thumb Turn sensor

The Matter sensor fits exactly like the Original thumb turn monitor. The difference is at the end: instead of a Locksure hub, you pair it with your smart home hub using the QR code in the box. Before you start, check you have one compatible smart home hub and that your lock passed the four fit checks.

In the box: the sensor with a CR2032 already fitted, the settings tool, the pairing QR code, adhesive pads and a quick-start guide, plus the spacers and thumb magnet used in the steps below.

1. How it fits together

The sensor sits on the plate below the cylinder; the magnet sits on the thumb turn rod.

2. Test the spacers

Hold the sensor against the plate with the barrel in the cut-out. Add spacers until about 1 mm of the barrel is exposed in front of the sensor face. Try before peeling anything.

3. Clean the lock plate

Wipe and let dry. Adhesive only grips a clean, dry plate.

4. Fit the spacers (if needed)

5. Wake the sensor

The battery is pre-fitted. Take it out and put it back in, positive side as marked. The lights flash to show the sensor is awake, and it is ready to pair for the next few minutes. If the sensor’s lights have stopped flashing during setup, take the battery out for a few seconds and put it back. The sensor starts setup again. If you pressed the settings pin, check afterwards that locking shows locked; if not, see Changing the setting (step 11).

6. Fit the sensor

Peel the backing, fit the U shape at the back of the sensor to the bottom of the barrel so they locate, and press for 20 seconds. Full strength after about 24 hours.

7. Move the thumb turn to the install position

Turn the thumb turn as far as it will go anti-clockwise, then back clockwise to the first vertical position. Leave it there while you fit the magnet.

8. Clean the thumb turn rod

9. Fit the thumb magnet

Peel the backing from the magnet, pick it up with the rectangular tool, seat it on the rod between the barrel and the thumb turn head aligned to the far edge of the rod as shown, and press for 20 seconds.

10. Test it

Lock: cyan flash. Unlock: amber flash. The lights do not stay on. If nothing flashes or the colours are reversed, see What the lights mean.

11. Changing the setting (optional)

Locks differ in which way they turn to lock. If your home app shows the wrong state after a turn, give the settings pin a short press (under a second) with the tool: the sensor moves to its next fitting setting and saves it straight away. Lock and unlock the door and check your home app shows locked when the door is locked; if not, press once more and test again. Holding the pin for a few seconds does nothing, so it is safe to let go. Holding it for about ten seconds or more factory resets the sensor: it is removed from your smart home and returns to setup mode, so only do that if you mean to add it again.

12. Add the Open/Close magnet (optional)

If you bought the £9.99 Open/Close Magnet: with the door closed, peel its backing, hold it on the frame beside the sensor and slide it upwards until the sensor’s green light flashes, then move it up one more millimetre and stick it down. Test by opening and closing the door. No pairing needed. Full detail in Fitting the Open/Close magnet.

13. Pair with your smart home

Open your home app, choose Add accessory (Apple Home) or add a device (Google Home, Alexa, SmartThings, Home Assistant), and scan the QR code on the card in the box. Stand near the door with your phone. Step-by-step for each app, and what to do if pairing fails, is in Pairing a Matter sensor.

Want the Locksure app as well? Download it (App Store or Google Play). On iPhone, tap + in the Locksure app, choose Lock Sensor and follow the steps: the app pairs the sensor through Apple Home for you. On Android, pair the sensor in Google Home first, then return to the Locksure app within a few minutes and tap Continue. The app is optional: the sensor works fully in your home app without it.

Specifications

Sensor size About 60 mm x 30 mm x 10.5 mm, 11 g
Radio Matter over Thread; Bluetooth for setup only
Battery CR2032, pre-fitted, replaceable; typically 18 months depending on use
Firmware updates Signed updates, started from the Locksure app

Was this page helpful?

Thank you. If you still need help, email support.

Back to the Help Centre